Side by Side RefrigeratorsDesign Guide With Installation InstructionsInstallationInstructions10-14 GEmonogram.com31-49057-1224D1889P015
1/4"1/2"3/4"1"1-1/4"1/4"1/2"3/4"1"1-1/4"1-1/2"23-7/8"From Rear of Refrigerator3/4" Ov
Design Guide111/4"1/2"3/4"1"1-1/4"1"3/4" OverlayPanel(Nominal Size)Stainless Steel1/4"1/2"3/4"2"
12DISPENSER TRIM FIT EXAMPLES:(NOT TO SCALE)3/4” OVERLAY PANEL(Flush Installation Only)• The dispenser trim fits over the custom panel and snaps into
13SIDE PANELSSide panels must be used whenever the sides of the refrigerator will be exposed. The 1/4” side panels will slip into the side case trim.
PARTS IDENTIFICATION:14Installation InstructionTrim, Freezer BottomTrim, Handle Side Visor, Fresh Food Trim, Handle Side Visor, FreezerTrim, Freezer H
GROUNDING THE REFRIGERATORWARNING Electrical Shock Hazard. Failure to follow these instructions can result in death, fire, or electrical shock.The p
Installation Instructions STEP 1 REMOVE PACKAGINGWARNING Tip Over Hazard. The refrigerator is much heavier at the top than at the ERWWRP³EHFDUHIX
17 STEP 4 INSTALLATION WITH HOUSEHOLD WATER FILTRATION SYSTEMSkip this step if you do not have a household water filtration systemIf the water supp
Standard Installation Only• Cut a 2” x 4” block, 35” long and secure the block to the mounting brackets provided using #12 or #14 wood screws.• Secure
STEP 11 REMOVE DOOR TRIM - FLUSH INSTALLATION ONLYUse the supplied Torx wrench or T10 Torx head driver to remove all exposed trim screws securing a
Safety Information2BEFORE YOU BEGIN Read these instructions completely and carefully.• IMPORTANT – Save these instructions for local inspector’s use.
20Installation Instructions STEP 12 LAYOUT DECORATIVE DOOR PANELS - FLUSH INSTALLATION ONLYDecorative wood panels must be cut to a thickness of 3/4”
STEP 13 ATTACH BRACKETS TO PANELS - FLUSH INSTALLATION ONLYLocate wood panel brackets and wood panel screws in Flush Inset Hardware Kit located ins
22Installation Instructions STEP 14 HANG DECORATIVE DOOR PANELS - FLUSH INSTALLATION ONLYPanels with attached brackets will mate with steel brackets
23Installation Instructions STEP 15 LAYOUT DECORATIVE GRILLE PANEL - FLUSH INSTALLATION ONLYGrille area will also have decorative wood panel attache
24Installation Instructions STEP 17 ADJUST DECORATIVE PANELS - FLUSH INSTALLATION ONLYEach door panel can be adjusted approximately 1/8” both left a
STEP 17 ADJUST DECORATIVE PANELS - FLUSH INSTALLATION ONLY (Cont)5. Make the final vertical adjustment of the fresh food and freezer door panels.
26 STEP 19 CONNECT WATER SUPPLY• Locate and bring the tubing to the front of the cabinet.• Turn the water on to flush debris from the line. Run about
27Installation Instructions STEP 22 INSTALL TOEKICKS• Locate the supplied toekicks (shipped taped to the side of the refrigerator.• Attach the LARGER
10-14 GEPrinted in the United StatesNOTE: While performing installations described in this book, safety glasses or goggles should be worn.For Monogram
AVERTISSEMENT Risque de basculement Ces réfrigérateurs présentent une partie supérieure lourde, en particulier avec une porte ouverte; ils doivent
4ContentsSafety 2, 3Planning GuideThe Installation Space 5Dimensions and Clearances 5Customization Basics 63/4” Overlay Panel Dimensions - Flush
BADesign GuideTHE INSTALLATION SPACEWater And Electrical Locations The opening must be prepared with the electrical and the cold water supply located
CUSTOMIZATION BASICS: Professional Style Stainless Steel RefrigeratorsStainless steel wrapped refrigerators have beveled edges and professional-style
7Design Guide3/4” OVERLAY PANEL DIMENSIONS(Flush Installation Only)For a more custom appearance, overlay panels may be installed to give a flush appea
1/4” FRAMED PANEL DIMENSIONS(Standard Installation Only)8If you choose to install framed panels, they must be cut to the dimensions shown. The panels
3/4” OVERLAY PANEL DIMENSIONS(Standard Installation Only)For a more custom appearance, overlay panels may be installed on trimmed models. The overlay
Comments to this Manuals