InstallationInstructions30″, 36″ and 48″ Custom Hood InsertZVC30LSSZVC36LSSZVC48LSS49-8041512-06 JRNETSPACE::rangehoods.comCall 1-800-667-8721 anywh
10Installation PreparationTOOLS AND MATERIALS REQUIRED(NOT SUPPLIED)Pencil and tape measureWire cutter/stripperStep ladderWire nutsPhillips and flat b
11Installation PreparationPARTS PROVIDEDLocate the parts packed with the hood.CHECK INSTALLATION HARDWARECount screws/components. Screws shown actual
12DUCTWORK, WIRING LOCATIONSDetermine the exact location of the insertsleeve. Mark the exact centerline location.The ceiling structure must be capable
13Plan the Location of the Hood and DuctworkThe ceiling structure must be capable of supporting theweight of the insert sleeve (approximately 100 poun
14Installation PreparationREMOTE MOUNTING OF THE CONTROL(WIRED)WARNING: Disconnect electricalpower from unit before beginning remote controlinstallati
15Installation PreparationREMOTE MOUNTING OF THE CONTROL(WIRED) (CONT.)COUNTERTOP 1. Cut out opening in the countertop. Cutoutdimensions are 1-11/16″
16Installation InstructionsSTEP 1 INSTALL HOOD LINER1. Frame the cutout opening to fit the liner. NOTE: The opening support must be 3/4″ thickwood to
17Installation InstructionsSTEP 2 CONNECT ELECTRICALVerify that power is turned off at the source.WARNING:If house wiring is not 2-wire with a ground
18Installation Instructions1. Tuck the house wiring out of the way.2. Install the insert sleeve into the cutout opening ofcustom cabinet frame.3. Push
19Installation InstructionsSTEP 4 INSTALL DAMPER PLATE1. Pick up damper plate assembly and rotate so thatvent side is up and bracket is located on le
2Installation InstructionsWARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:A. Use this unit only in the
20Installation InstructionsSTEP 5 INSTALL BLOWER MOTOR1. Pick up blower motor and rotate so tabs align with damper plate bracket.2. Insert blower mot
21Installation InstructionsSTEP 7 INSTALL FILTERS1. Remove protective film from the filters.2. Tip the filter into the back tab slots and lift up.Whi
3Installation InstructionsAVERTISSEMENT : AFIN DE RÉDUIRE LE RISQUE D’INCENDIE, DE CHOCS ÉLECTRIQUES OU DE BLESSURES CORPORELLES,VEUILLEZ VOUS CONFORM
4Design InformationCONTENTSDesign InformationProduct Clearances ...4Product Dim
5Design InformationPRODUCT DIMENSIONS4″28-1/2″21-1/4″27-1/2″14″16-3/4″25-3/4″13″14″1/2″1-1/4″7-1/2″The bottom edge of the insert sleeve has a 7/8″wide
6Design InformationPRODUCT DIMENSIONS4″34-1/2″21-1/4″27-1/2″14″16-3/4″25-3/4″13″14″1/2″4-1/4″7-1/2″The bottom edge of the insert sleeve has a 7/8″wide
7Design InformationPRODUCT DIMENSIONS4″46-1/2″21-1/4″1/2″3-7/8″7-1/2″A 1/2″ wide flange surrounds the outside edge ofthe insert sleeve.Remote Location
Advance PlanningADVANCE PLANNINGDuctwork Planning•This hood is equipped for 8″ round ductwork. •Determine the exact location of the vent hood.•Plan th
DUCT FITTINGSUse this chart to compute maximum permissible lengths forduct runs to outdoors.NOTE: Do not exceed maximumpermissible equivalent lengths!
Comments to this Manuals